specifies the username to connect as. If this is not given, then the environment variable USER is used. This option can also take the form "user%password" or "workgroup/user" or "workgroup/user%password" to allow the password and workgroup to be specified as part of the username.

specifies the CIFS password. If this option is not given then the environment variable PASSWD is used. If the password is not specified directly or indirectly via an argument to mount mount.cifs will prompt for a password, unless the guest option is specified.

Note that a password which contains the delimiter character (i.e. a comma ',') will fail to be parsed correctly on the command line. However, the same password defined in the PASSWD environment variable or via a credentials file (see below) or entered at the password prompt will be read correctly.

specifies a file that contains a username and/or password. The format of the file is:

		username=value
		password=value

This is preferred over having passwords in plaintext in a shared file, such as /etc/fstab. Be sure to protect any credentials file properly.

sets the uid that will own all files on the mounted filesystem. It may be specified as either a username or a numeric uid. This parameter is ignored when the target server supports the CIFS Unix extensions.

sets the gid that will own all files on the mounted filesystem. It may be specified as either a groupname or a numeric gid. This parameter is ignored when the target server supports the CIFS Unix extensions.

sets the port number on the server to attempt to contact to negotiate CIFS support. If the CIFS server is not listening on this port or if it is not specified, the default ports will be tried i.e. port 445 is tried and if no response then port 139 is tried.

When mounting to servers via port 139, specifies the RFC1001 source name to use to represent the client netbios machine name when doing the RFC1001 netbios session initialize.

If the server does not support the CIFS Unix extensions this overrides the default file mode.

If the server does not support the CIFS Unix extensions this overrides the default mode for directories.

sets the destination host or IP address.

sets the domain (workgroup) of the user

don't prompt for a password

Charset used to convert local path names to and from Unicode. Unicode is used by default for network path names if the server supports it. If iocharset is not specified then the nls_default specified during the local client kernel build will be used. If server does not support Unicode, this parameter is unused.

mount read-only

mount read-write

If the CIFS Unix extensions are negotiated with the server the client will attempt to set the effective uid and gid of the local process on newly created files, directories, and devices (create, mkdir, mknod).

The client will not attempt to set the uid and gid on on newly created files, directories, and devices (create, mkdir, mknod) which will result in the server setting the uid and gid to the default (usually the server uid of the user who mounted the share). Letting the server (rather than the client) set the uid and gid is the default. This parameter has no effect if the CIFS Unix Extensions are not negotiated.

Client does permission checks (vfs_permission check of uid and gid of the file against the mode and desired operation), Note that this is in addition to the normal ACL check on the target machine done by the server software. Client permission checking is enabled by default.

Client does not do permission checks. This can expose files on this mount to access by other users on the local client system. It is typically only needed when the server supports the CIFS Unix Extensions but the UIDs/GIDs on the client and server system do not match closely enough to allow access by the user doing the mount. Note that this does not affect the normal ACL check on the target machine done by the server software (of the server ACL against the user name provided at mount time).

Do not do inode data caching on files opened on this mount. This precludes mmaping files on this mount. In some cases with fast networks and little or no caching benefits on the client (e.g. when the application is doing large sequential reads bigger than page size without rereading the same data) this can provide better performance than the default behavior which caches reads (readahead) and writes (writebehind) through the local Linux client pagecache if oplock (caching token) is granted and held. Note that direct allows write operations larger than page size to be sent to the server. On some kernels this requires the cifs.ko module to be built with the CIFS_EXPERIMENTAL configure option.

Translate six of the seven reserved characters (not backslash, but including the colon, question mark, pipe, asterik, greater than and less than characters) to the remap range (above 0xF000), which also allows the CIFS client to recognize files created with such characters by Windows's POSIX emulation. This can also be useful when mounting to most versions of Samba (which also forbids creating and opening files whose names contain any of these seven characters). This has no effect if the server does not support Unicode on the wire.

Do not translate any of these seven characters (default)

currently unimplemented

(default) currently unimplemented

The program accessing a file on the cifs mounted file system will hang when the server crashes.

(default) The program accessing a file on the cifs mounted file system will not hang when the server crashes and will return errors to the user application.

Print additional debugging information for the mount. Note that this parameter must be specified before the -o. For example:

mount -t cifs //server/share /mnt --verbose -o user=username

Do not allow POSIX ACL operations even if server would support them.

The CIFS client can get and set POSIX ACLs (getfacl, setfacl) to Samba servers version 3.10 and later. Setting POSIX ACLs requires enabling both XATTR and then POSIX support in the CIFS configuration options when building the cifs module. POSIX ACL support can be disabled on a per mount basic by specifying "noacl" on mount.

Use inode numbers (unique persistent file identifiers) returned by the server instead of automatically generating temporary inode numbers on the client. Although server inode numbers make it easier to spot hardlinked files (as they will have the same inode numbers) and inode numbers may be persistent (which is userful for some sofware), the server does not guarantee that the inode numbers are unique if multiple server side mounts are exported under a single share (since inode numbers on the servers might not be unique if multiple filesystems are mounted under the same shared higher level directory). Note that not all servers support returning server inode numbers, although those that support the CIFS Unix Extensions, and Windows 2000 and later servers typically do support this (although not necessarily on every local server filesystem). Parameter has no effect if the server lacks support for returning inode numbers or equivalent.

client generates inode numbers (rather than using the actual one from the server) by default.

(default) Do not allow getfattr/setfattr to get/set xattrs, even if server would support it otherwise.

default network read size

default network write size